Bathroom vanity sizing Brisbane showroom measure guide

The vanity photo looked perfect until the tiler asked for projection clear of the door swing and the plumber asked where the waste sat relative to the cabinet carcass. Most vanity regrets we hear from Brisbane renovators are sizing and set-out problems - not finish preference - and they show up after waterproofing closes.

This bathroom vanity sizing measure guide helps you measure wall width, projection, basin clearances and mount type before you order. Confirm every figure on the product page and with your plumber and tiler.

Photos flatten width and projection

Fact: a vanity needs clear wall width, door and drawer swing, and a basin or top that matches the mixer reach. Online photos hide how far the cabinet sits proud of the wall and how the door clears the shower screen or toilet pan.

Truth from the floor: the cabinets we re-work most often were chosen without a measured wall width and without confirming waste position against the rough-in. Twenty minutes at the Loganholme showroom with a room sketch and tape measure beats a late carcass swap. Brisbane context: bathroom vanities Brisbane.

What to measure before you order a vanity

• Wall width between returns - measure the clear run where the cabinet will sit, not the overall room width. Note any nib walls, windows and pipe chases.
• Projection from the wall - how far the cabinet and basin can sit into the room without blocking door swing, toilet clearance or the shower entry.
• Basin and top clearances - bowl width, tap-hole count and mixer reach must work with the cabinet top. Read basin sizing guide beside the vanity selection.
• Mount type and wall structure - wall-hung needs adequate nogging or structure; freestanding sits on the slab. Compare vanity mount types and wall-hung vs freestanding vanity.
• Drawer and door swing - open drawers on the floor display so soft-close depth feels real next to your sketch.
• Waste and service access - note existing waste location and whether the cabinet back or removable panel allows service after install.

Shop the mother range: bathroom vanities. Small ensuite notes: freestanding vs wall-hung vanity for small Brisbane bathrooms.

Showroom measure rhythm at Loganholme

1. Bring the room sketch - wall lengths, door swing, window line and any existing waste photo with a tape in frame.
2. Choose two widths - not twenty screenshots. A single-bowl run versus a double-bowl elevation is the first fork for most Brisbane and Logan wet areas.
3. Stand the footprint - tape the cabinet width and projection on the showroom floor so walking clearances feel real.
4. Check basin and mixer together - hold a basin and mixer sample against the top under the same LEDs you will live with.
5. Confirm mount path - wall-hung brackets versus freestanding plinth. Lock the path in writing before you leave.
6. Write the SKUs - cabinet handle, basin type, mixer finish and any mirror pairing before you order.

Plan the visit via bathroom showroom Brisbane and the showroom hours page. What to bring checklist: showroom what to bring.

Mount, basin and finish pairing without unpublished specs

Start with measured width and projection, then choose mount type from structure and cleaning habits - not trends alone. Pair basins and tapware early so spout reach and tap holes match the top:

• Vanities - wall-hung, freestanding, single and double bowl options side by side
• Basins - confirm bowl width and tap holes on the product page
• Tapware - lock one finish family for mixer and nearby accessories
• Mirrors - centre the mirror elevation after the vanity width is locked
• Mount reading: vanity mount types | wall-hung vs freestanding
• Finish walk when stock allows: shop by finish

Related Brisbane pages and guides: vanities Brisbane | basins Brisbane | tapware Brisbane | wall-hung vanity and LED mirror pairing | bathroom renovation checklist | bathroom buying guides.

Large vanity crates may ship on a specialised carrier -

Visit and shop next steps

Shop and pages: vanities | bathroom vanities Brisbane | vanity mount types | basin sizing | bathroom buying guides.

Bring your room sketch and tape measure to our Loganholme showroom. Check vanity width, projection and basin clearances under real light so install week is about fitting the cabinet you already measured - not redesigning the elevation on the fly.

Widths and depths in our range

Most of our wall hung vanities from Otti and Aulic come in six standard widths: 600, 750, 900, 1200, 1500 and 1800mm. Aulic also has 450mm mini cabinets for powder rooms, and many Aulic models list an overall depth of 460mm, which is the figure to check against your door swing. For two basins, double bowl vanities in our range start at 1200mm; the double bowl notes cover the plumbing.

Brand overviews: Otti | Aulic | ADP. Each product page lists the exact width, depth and top options, so measure your wall first and then compare. You can stand in front of different widths at our Loganholme showroom.

Visit, delivery and contact

Our showroom is at Shop 4, 1 Bryants Rd, Loganholme QLD 4129 (opening hours and directions), where you can see finishes in person and collect your order free once it is ready. We also deliver Australia-wide, with the exact rate shown at checkout (see delivery and returns). Questions? Call 07 3209 9644 or send us a message.